![]() ![]() The ping should be successful and you should be able to connect to the Miniserver. Follow these steps to setup and ping the Miniserver.ħ.1 Setup is successful and the Miniserver is on the same subnet as your router. Important: The network must be classified as a home or workplace network on your Windows PC! You can now connect to the Miniserver, if not please go to step 6.Ħ. ![]() If you are using Parallels software on a Macbook make sure that your network is bridged not shared! You can now connect to the Miniserver, if not please go to step 5.ĥ. Some antivirus software will still block outgoing traffic with Loxone Config even if you have done this so it is best to temporarily disable antivirus programs when using Loxone Config. Check whether you have not made an exception for Loxone Config in your firewall or antivirus software. You can now connect to the Miniserver, if not please go to step 4.Ĥ. Check again that the network cable is connected correctly. If no Miniserver is listed in the search results continue to step 3.ģ. The Miniserver should show up in the search results and you can connect to it by double clicking on it. Open Loxone Config and search for the Miniserver. The Miniserver status LEDs should be flashing green and the network socket LEDs should be green on and amber flashing. If the LEDs stay the same pleasecontact support.ġ.3 If both LEDs are on constantly, with or without a cable connected please contact support.Ģ. If this is all correct continue to step 2.ġ.2 If both or one LED is not flashing/not lit up then check first that the network cable is connected correctly and the cable has been tested or replaced. Verify that the status LEDs on the network (LAN) port of the flash or are lit up.ġ.1 The green LED should be lit constantly, the amber LED should flash. If the Miniserver is flashing green but you cannot connect to it in Loxone Config use the following table to resolve the issue: Stepġ. There is a faulty PLC program in the Miniserver. If the behaviour remains the same then format the SD card to factory defaults according to the instructions. Check that the SD card is inserted correctly.Ģ. Reboot the Miniserver and extensions (by turning the power supply off for about 10 seconds until rebooting). The green connector power plug should NOT be removed if the power supply is on.ģ. The Miniserver does not recognise the SD card or cannot access the card.ġ. If this is not the case refer to the following table for the solution: LED statusġ. Reboot the Miniserver and extensions (by turning the power supply off for about 10 seconds until rebooting). The green connector power plug should NOT be removed if the power supply is on.Ģ. After this process the status LED on the front of the Miniserver will be flashing green. The boot process takes about 7-10 seconds. Only power up the Miniserver once all wiring has been completed. At the time of review, all components must be installed and fully functional.Unpack your Miniserver from its box and connect the power supply as well as a network cable from the router to the Miniserver. – Loxone Water Sensors in appropriate roomsĪ Loxone Partner Consultant will review each project you submit for the Smart Home Bonus. – Loxone Smoke Detector in designated rooms* – Loxone Touch/Touch Pure/Touch Surface for control in each room – Loxone Valve Actuators for zoned heating control for each room/zone – The shading should be controlled either by a Geiger motor, our Shading Actuator or our Relay Extension – A Motion Sensor Tree in each room (unless using our Ceiling Light with inbuilt motion sensor) – A minimum of 80% of the lighting should be Loxone Tree. The following hardware must be included in a Loxone Smart Home project: To qualify, the following functions must be commissioned: The 3% bonus will be in the form of a credit note on your account. The Smart Home Bonus is available on projects where the components were purchased after. Have you commissioned a true Loxone Smart Home? If so, you’ll effectively receive an addition 3% discount off the list price of all the Loxone components you’ve used in this project. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |